噴淋清洗機在工業生產、汽車維修、餐飲等多個領域都有廣泛應用，以下是其使用要點：

Spray cleaning machines are widely used in various fields such as industrial production, automotive maintenance, and catering. The following are the key points for their use:

前期準備

preparation in advance

檢查設備：在使用噴淋清洗機前，要仔細檢查設備的各個部件是否正常。包括噴頭是否堵塞、管道是否有泄漏、泵體是否能正常運轉、電氣系統是否存在故障等。若發現問題，應及時維修或更換部件，以確保設備能正常運行。

Check the equipment: Before using the spray cleaning machine, carefully inspect all components of the equipment to ensure they are functioning properly. Including whether the nozzle is blocked, whether there is leakage in the pipeline, whether the pump body can operate normally, and whether there are any faults in the electrical system. If any problems are found, they should be repaired or replaced in a timely manner to ensure that the equipment can operate normally.

選擇合適的清洗劑：根據被清洗物體的材質、污垢類型和程度來選擇合適的清洗劑。例如，對于金屬表面的油污，可選用堿性清洗劑；對于水垢，可使用酸性清洗劑；對于塑料或玻璃制品，要選擇溫和、無腐蝕性的清洗劑，以免對物體造成損害。同時，要按照清洗劑的使用說明進行稀釋和調配，確保濃度合適。

Choose the appropriate cleaning agent: Choose the appropriate cleaning agent based on the material, type, and degree of dirt of the object being cleaned. For example, alkaline cleaning agents can be used for oil stains on metal surfaces; For scale, acidic cleaning agents can be used; For plastic or glass products, choose a mild and non corrosive cleaning agent to avoid damage to the object. At the same time, dilute and mix according to the instructions for using the cleaning agent to ensure the appropriate concentration.

準備被清洗物品：將需要清洗的物品進行適當的預處理，如去除較大的污垢、松散的雜質等，以免這些雜質進入清洗機，堵塞噴頭或影響清洗效果。對于一些易損壞或有特殊要求的物品，要采取相應的保護措施，如使用夾具固定、包裹易碎部位等。

Prepare the items to be cleaned: Pre treat the items to be cleaned appropriately, such as removing large dirt, loose impurities, etc., to prevent these impurities from entering the cleaning machine, blocking the nozzle, or affecting the cleaning effect. For some items that are easily damaged or have special requirements, corresponding protective measures should be taken, such as using fixtures to fix them, wrapping fragile parts, etc.

操作過程

Operation process

設置參數：根據被清洗物品的特點和清洗要求，合理設置噴淋清洗機的各項參數。一般包括清洗時間、噴淋壓力、溫度等。清洗時間通常在幾分鐘到幾十分鐘不等，可根據污垢的頑固程度進行調整；噴淋壓力要適中，壓力過低可能無法有效去除污垢，壓力過高則可能會對物品表面造成損傷，一般在 0.5-2MPa 之間；溫度方面，有些清洗劑在一定溫度下能發揮更好的清洗效果，常見的清洗溫度在 40-80℃之間，但對于一些不耐高溫的物品，要選擇較低的溫度。

Set parameters: Based on the characteristics and cleaning requirements of the item to be cleaned, reasonably set the various parameters of the spray cleaning machine. Generally includes cleaning time, spray pressure, temperature, etc. The cleaning time usually ranges from a few minutes to several tens of minutes, and can be adjusted according to the degree of stubborn dirt; The spray pressure should be moderate. If the pressure is too low, it may not effectively remove dirt, and if the pressure is too high, it may cause damage to the surface of the object, usually between 0.5-2MPa; In terms of temperature, some cleaning agents can achieve better cleaning effects at a certain temperature. The common cleaning temperature is between 40-80 ℃, but for some items that are not heat-resistant, a lower temperature should be chosen.

正確放置物品：將被清洗物品均勻地放置在清洗機的傳送帶上或清洗籃內，確保物品之間有足夠的間隙，以便噴淋液能夠充分接觸到物品的各個表面，達到全面清洗的效果。同時，要注意物品的放置方向，避免有死角或遮擋，影響清洗質量。

Proper placement of items: Place the items to be cleaned evenly on the conveyor belt or in the cleaning basket of the cleaning machine, ensuring sufficient clearance between the items so that the spray liquid can fully contact all surfaces of the items, achieving a comprehensive cleaning effect. At the same time, attention should be paid to the placement direction of items to avoid blind spots or obstructions that may affect the quality of cleaning.

監控清洗過程：在清洗機運行過程中，要密切觀察清洗情況。注意噴淋液的噴射狀態是否正常，是否有噴頭堵塞或噴淋不均勻的現象；檢查清洗機的運行聲音是否平穩，有無異常振動或噪音；關注清洗液的液位和溫度變化，及時補充或調整。如果發現問題，應立即停機檢查，排除故障后再繼續運行。

Monitor the cleaning process: During the operation of the cleaning machine, closely observe the cleaning situation. Pay attention to whether the spraying state of the spray liquid is normal, and whether there is any blockage or uneven spraying of the nozzle; Check whether the operating sound of the cleaning machine is stable, and whether there are any abnormal vibrations or noises; Pay attention to changes in the liquid level and temperature of the cleaning solution, and promptly replenish or adjust it. If any problems are found, the machine should be stopped immediately for inspection and troubleshooting before resuming operation.

清洗后處理

Post cleaning treatment

干燥處理：清洗完成后，要對清洗后的物品進行干燥處理。可根據物品的材質和要求，選擇自然晾干、吹干或烘干等方式。對于一些對干燥速度要求較高或不允許有水分殘留的物品，可采用熱風吹干或烘干的方法，但要注意控制溫度和時間，防止物品變形或損壞。

Drying treatment: After cleaning, the cleaned items should be dried. According to the material and requirements of the item, natural air drying, blow drying, or drying methods can be selected. For some items that require high drying speed or do not allow moisture residue, hot air blowing or drying methods can be used, but attention should be paid to controlling the temperature and time to prevent deformation or damage of the items.

設備清潔與維護：及時清理清洗機內部的污垢和雜質，排放清洗液，并對設備進行沖洗，防止污垢和殘留的清洗劑對設備造成腐蝕。定期更換過濾器、密封圈等易損部件，對泵體、噴頭等關鍵部件進行檢查和保養，確保設備處于良好的運行狀態。

Equipment cleaning and maintenance: Timely clean the dirt and impurities inside the cleaning machine, discharge the cleaning solution, and rinse the equipment to prevent corrosion caused by dirt and residual cleaning agents. Regularly replace vulnerable components such as filters and seals, inspect and maintain key components such as pump bodies and nozzles, and ensure that the equipment is in good operating condition.

清洗劑處理：對使用過的清洗劑要進行妥善處理，避免對環境造成污染。對于含有有害物質的清洗劑，應按照環保要求進行回收或處理，可通過專業的污水處理設備進行凈化處理，使其達到排放標準后再排放。

Cleaning agent treatment: Used cleaning agents should be properly treated to avoid polluting the environment. For cleaning agents containing harmful substances, they should be recycled or treated according to environmental requirements. They can be purified by professional sewage treatment equipment to meet discharge standards before being discharged.

本文由噴淋清洗機友情奉獻.更多有關的知識請點擊: http://m.glwh.com.cn真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

This article is a friendly contribution from the spray cleaning machine For more information, please click: http://m.glwh.com.cn Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.